LX3000-LX4000
How do I replace the Print Head Lid Nozzle Assembly? (LX3000/LX4000)
Nozzles on the Print Head lid connect to the tanks on the side and drip ink into the each color compartment in the print head. If one of these nozzles breaks or is cracked this system no longer works. You can purchase replacement nozzles and install ...
How to Change the Ethernet connection from Static to DHCP or vice versa (Eddie/LX3000/LX4000).
All changes to the Ethernet setup can be made using the original installer program. Click the button for "Software for PC" on this page: Eddie: https://www.primera.com/eddiedownloads LX3000: https://www.primera.com/lx3000downloads Tip: Run the ...
How to convert a Dye Ink LX3000/LX4000 to a Pigment LX3000/LX4000 or vice versa.
Pigment and Dye LX3000s have identical parts. Pigment and Dye LX4000s have identical parts. The only difference is the type of ink tanks and print heads that come in the box. Once you use the print head and tanks, that type of ink starts to flow into ...
LX3000 - Empty Ink Error but Ink is not Empty. PrintHub Software or Mac Config Utility says my ink tanks are empty but I can see there is still ink left.
Error explanation: Ink usage is calculated by the software, not a physical sensor(gas gauge). Between printer uses, some ink bleeds out of the ink lines and back into the tank. When you start printing again, it takes some time for the ink to make its ...
Printing is Blurry in some sections, has a shadow effect or is double printing. (LX3000)
There are several possible reasons for this. 1. First, let's try a cartridge alignment. 2. Set Bi-di Printing to NO. Just before printing, you will have the option to adjust these settings. In BarTender click Document Properties. On a Mac, you ...
How to enable External Feed Mode on the LX3000/LX4000 so you may feed labels from an external powered unwinder.
In Primera PrintHub on PC, Go to Printer Settings - Advanced Settings Button. Check the Disable Unwinder/External Feed Mode box to disable the loops sensor so that you may feed label stock from an external powered unwinder through the slot on the ...
Simultaneous Flashing Pause and Ink Lights. Printer will not print. (LX3000).
This flashing light sequence (shown below) indicates a missing ink tank or print head. If the ink tank or print head is installed try the following solutions. 1. Update PrintHub/Config Utility and Firmware to resolve this issue. HC11 firmware should ...
Tank PEN Mismatch Error (LX3000/LX4000)
This error indicates that the print head ink type (dye or pigment) does not match ink tank types installed. (Note: it is also possible that one of the three in tanks is the wrong type.) You must match the correct print head with the ink tanks. To fix ...
Wiper Error or Interface Error (LX910, LX3000, LX4000, LX600, LX610, Eddie)
This error indicates that the motor that controls the wiper movement is stalling. This may be due to an obstruction in the path of the wiper. 1. Ensure the cartridge cap is functioning properly. Please view this video for instructions. ...
LX3000/LX4000 Shipping Instructions
The Primera LX3000 and LX4000 Color Label Printer uses separate ink tanks that carry ink through an ink tube system. To prevent spills/leaks during shipping, special precautions must be taken. These instructions explain how to seal the ink system ...
Long labels are not feeding straight or printing crooked. Labels over 12 inches do not feed - display TOF Error. (LX910, LX3000, LX4000)
When labels are loaded for the first time, the printer attempts to find the gap between the first label and the second label. This is used to calibrate the length of the label and calibrate the gap sensor to look for similar gaps every x number of ...
Ink Tank Missing/Unknown Error (LX3000/LX4000)
Make sure you follow the procedure in the setup video to install the ink tanks properly. If all tanks are installed, and you receive this error, please try the following in this order. 1. Update to the latest firmware. This will ensure you receive an ...
How does the LX3000/LX4000 Ink system work? What are best practices?
The ink system is a sealed system that uses atmospheric pressure and properties of fluid mechanics to feed a prefilled printhead from off-carrier Ink Tanks. There is no pump necessary and the ink tubes are relatively short. The system is unlikely to ...
The LX3000/LX4000 Print Head is printing with Poor Quality, Banding, Streaks, or Missing Colors.
You may need to replace your print head. The nozzles can wear out over time. Tip! Leave the printer powered on when it is not in use to maintain cartridge readiness! 1. Clean / Test Print. Print the Clean/Test Print described in this article. Send us ...
Can I print wirelessly to my Primera Printer? (LX3000, LX4000 and Eddie)
The Eddie, LX3000, LX4000 or Catalyst can be used out of the box with a USB connection or Ethernet connection. You can purchase a BrosTrend Wifi Range Extender with an Ethernet port to connect the printer to a wireless network. You can then print to ...
Can I open the print head lid on my LX3000/LX4000?
Occasionally you may need to remove the printhead to clean the nozzles. Use the instructions in the video below. You may open and close the lid up to 8 times before the print head will lose its prime and need to be replaced. Each time you open the ...