LX3000
How to Change the Ethernet connection from Static to DHCP or vice versa (Eddie/LX3000).
All changes to the Ethernet setup can be made using the original installer program. Click the button for "Software for PC" on this page: Eddie: https://www.primera.com/eddiedownloads LX3000: https://www.primera.com/lx3000downloads Tip: Run the ...
How to convert a Dye Ink LX3000 to a Pigment LX3000 or vice versa.
All LX3000s have identical parts. However, the model can be purchased in two variations: Dye or Pigment Ink. The only difference is the type of ink tanks and print heads that come in the box. Once you use the print head and tanks, that type of ink ...
LX3000 - Empty Ink Error but Ink is not Empty. PrintHub Software or Mac Config Utility says my ink tanks are empty but I can see there is still ink left.
Error explanation: Ink usage is calculated by the software, not a physical sensor(gas gauge). Between printer uses, some ink bleeds out of the ink lines and back into the tank. When you start printing again, it takes some time for the ink to make its ...
Printing is Blurry in some sections, has a shadow effect or is double printing. (LX3000)
There are several possible reasons for this. 1. First, let's try a cartridge alignment. 2. Set Bi-di Printing to NO. Just before printing, you will have the option to adjust these settings. In BarTender click Document Properties. On a Mac, you ...
How to enable External Feed Mode on the LX3000 so you may feed labels from an external unwinder (LX3000).
In Primera PrintHub on PC, Go to Printer Settings - Advanced Settings Button. Check the Disable Unwinder/External Feed Mode box to disable the loops sensor so that you may feed label stock from an external unwinder through the slot on the back of the ...
Simultaneous Flashing Pause and Ink Lights. Printer will not print. (LX3000).
This flashing light sequence (shown below) indicates a missing ink tank or print head. If the ink tank or print head is installed try the following solutions. 1. Update PrintHub/Config Utility and Firmware to resolve this issue. HC11 firmware should ...
Tank PEN Mismatch Error (LX3000).
This error indicates that the print head ink type (dye or pigment) does not match ink tank types installed. (Note: it is also possible that one of the three in tanks is the wrong type.) You must match the correct print head with the ink tanks. To ...
Wiper Error or Interface Error (LX910, LX3000, LX600, LX610, Eddie)
This error indicates that the motor that controls the wiper movement is stalling. This may be due to an obstruction in the path of the wiper. 1. Ensure the cartridge cap is functioning properly. Please view this video for ...
LX3000 Shipping Instructions
The Primera LX3000 Color Label Printer uses separate ink tanks that carry ink through an ink tube system. To prevent spills/leaks during shipping, special precautions must be taken. These instructions explain how to seal the ink system with the ...
Ink Tank Missing/Unknown Error (LX3000)
Make sure you follow the procedure in the setup video to install the ink tanks properly. If all tanks are installed, and you receive this error, please try the following in this order. 1. Update to the latest firmware. This will ensure you receive an ...
How does the LX3000 Ink system work? What are best practices?
The LX3000 ink system is a sealed system that uses atmospheric pressure and properties of fluid mechanics to feed a prefilled printhead from off-carrier Ink Tanks. There is no pump necessary and the ink tubes are relatively short. The system is ...
The LX3000 Print Head is printing with Poor Quality, Banding, Streaks, or Missing Colors.
You may need to replace your print head. The nozzles can wear out over time. 1. Clean / Test Print. Print the Clean/Test Print described in this article. Send us a picture of the clean/test print! 2. Ink may not be flowing to the print head from the ...
Can I print wirelessly to my Primera Printer? (LX3000 and Eddie)
The Eddie, LX3000 or Catalyst can be used out of the box with a USB connection or Ethernet connection. You can purchase a BrosTrend Wifi Range Extender with an Ethernet port to connect the printer to a wireless network. You can then print to it ...
Can I open the print head lid on my LX3000?
Occasionally you may need to remove the printhead to clean the nozzles. Use the instructions in the video below. You may open and close the lid up to 8 times before the print head will lose its prime and need to be replaced. Each time you open the ...