The computer or the Disc Publisher does not recognize that the ADL-MAX is connected. The ADL-MAX is not being used even though it is connected.
The computer or the Disc Publisher does not recognize that the ADL-MAX is connected. The ADL-MAX is not being used even though it is connected.
Two components need to be installed in order to use the ADL-MAX with a Disc Publisher.
1. ADL-MAX Driver. When you first connected the ADL-MAX to the computer you should have been prompted with a Found New Hardware wizard. As long as you clicked Automatically Install in the hardware wizard and you had the original installation disc in the computer's CD drive, the driver should have been installed. To check if the driver was installed, connect the ADL-MAX via USB and plug in the power adapter. Right click on My Computer on your desktop - Choose Properties - Click the Hardware Tab - Click Device Manager - Open the USB Section. ADL-MAX Driver should be listed.
Note: To reinstall, right-click on ADL-MAX Driver and click uninstall. Now unplug power from the ADL-MAX and plug power back in after several seconds. The Found New Hardware wizard should appear. Install the driver using the installation disc or download it from the Printer Driver page.
If ADL-MAX Driver is not listed in device manager, make sure the ADL-MAX is connected via USB and restart the computer. The found new hardware wizard should appear. If it still does not appear, check to make sure you are following the USB connection guidelines below:
Hubs. USB hubs or pass-through ports on other devices are not recommended.
Port Location. Even with onboard ports, always use the ports on the back of the computer. These ports are located directly on the motherboard. If you are using a front port, you are likely connected to a hub. It is just located inside the computer rather than outside.
Combo Cards. Stay away from combo cards. (Combo cards are cards that do other things in addition to USB 2.0 or Firewire. Example: 2 firewire ports, 2 USB 2.0 ports and one serial port)
2. Updated Robotic Files. Make sure the Primo DVD Robotic files were updated. Open My Computer on your desktop - Choose the "C" Drive - Open the Program Files folder - Open PrimoDVD (English). Check that the modified date on both of the files shown below is 11-1-2006 or later.
If the files are not updated delete and reinstall the latest version of Primo using the instructions in this article.
3. Update the firmware on your Bravo. This may be required for some Bravo products released before the ADL-MAX. Check the firmware update page.
Article ID: 45034Related Articles
The ADL-MAX is not picking discs from the printer tray after the Disc Publisher prints a disc.
The ADL-MAX is not picking discs from the printer tray after the Disc Publisher prints a disc. 1. ADL-MAX Placement. You must Place the ADL-MAX on a flat surface with less than 1/16 inch sag. Placing the ADL-MAX on an uneven surface may result in ...No Response. Make sure the Disc Publisher is powered on and the USB cable is connected.
No Response. Make sure the Disc Publisher is powered on and the USB cable is connected. There are several things to check. 1. Local Admin Rights. You must be have local administrative rights to the PC running the Bravo. You may be able to print ...How do I load the ADL-MAX bins?
How do I load the ADL-MAX bins? The far left bin of the ADL-MAX and the left bin of the Disc Publisher should be empty. The front left bin is the first bin that discs are picked from. The left bin of the Disc Publisher is used for rejects. See the ...How do I calibrate the ADL-MAX bins? How do I re-calibrate the Disc Publisher tray and drive(s) to the ADL-MAX?
How do I calibrate the ADL-MAX bins? How do I re-calibrate the Disc Publisher tray and drive(s) to the ADL-MAX? The first time you open the PrimoDVD or RoboPrint software you will be prompted to calibrate the ADL-MAX to the Disc Publisher. The pick ...PTProtect: "0 discs left" appears even though the dongle is connected -or- the three free protections were never available. "0 discs left" was displayed immediately after installing PTPublisher 1.3.0. or higher (Windows Vista / 7 / 8 Only).
PTProtect: "0 discs left" appears even though the dongle is connected -or- the three free protections were never available. "0 discs left" was displayed immediately after installing PTPublisher 1.3.0. or higher (Windows Vista / 7 / 8 Only). Method ...